Calibration blank 98 x 10 mm, for Tizian Cut 5 smart / Cut 5 smart Plus
Description
Blanks for the calibration of your Tizian Cut 5 Smart or Tizian Cut 5 Smart Plus
Product number:
523615
Questions about the product? We are glad to be here for you!
Product information "Calibration blank 98 x 10 mm, for Tizian Cut 5 smart / Cut 5 smart Plus"
Use these blanks made of polyurethane foam to carry out test millings in the process of calibrating or re-measuring your Tizian Cut 5 Smart or Tizian Cut 5 Smart Plus. Produce special test copings to measure subsequently. Enter this data into the control system of milling machine.
Cutsomers also bought
T2/T7 Tizian Cut 5/3.5 Metal Drill CoCr/Ti 2mm, 6 mm shaft
Radius cutter short, double-edged, edge Ø 2 mm, shaft Ø 6 mm, total length 45 mm. Max. blank height = short up to 15 mm, long up to 20 mm. Processing type: roughing Blank material: CoCr, titanium Type: coated Coding color: gold For the milling machines: Tizian Cut 5.2, Tizian Cut 5.2 plus, Tizian Cut 5 option metal milling (6 mm shaft), CORiTEC 550i, CORiTEC 750i
T3/T8 Tizian Cut 5/3.5 ball-headed metal drill 1,5, CoCr/Ti balltop
Ball-end mill, double-edged, edge Ø 1.5 mm, shaft Ø 6 mm, total length 48 mm Processing type: drilling a screw channel Blank material: CoCr, titanium Type: coated Coding color: gold For the milling machines: Tizian Cut 5.2, Tizian Cut 5.2 plus, Tizian Cut 5 option metal milling (6 mm shaft), CORiTEC 550i, CORiTEC 750i
Tizian Blank PMMA Splint 98 mm
Tizian Blank PMMA Splint is made of a highly pure themoplastic PMMA which is produced following the highest quality standards. The crystal clear, color-stable material stands out with its homogeneity, low plaque adhesion and low water absorption. Tizian Blank PMMA Splint is an economic alternative for the splint technology. It can be be repaired and extended with PMMA acrylics. Indications: Occlusion splints Drilling templates for navigated implantation Lost wax technique in casting technology Processing: Due to the chemical and physical properties of thermoplastic PMMA, there is a risk of melting the material during dry machining and thus smearing the mills. Therefore, it is important to use only single-edged mills. If necessary, the milling strategy must be adjusted with a slower cutting speed and a lower feed rate. The material can be processed by wet machining with PMMA mills in a standard strategy without restrictions.
T61 Tizian Cut 5/3.5 radius cutter 3.0 mm for Titan/CoCr, 4-bladed, 6 mm shaft
T61 - metal roughing tool The complex geometry of the four high-capacity cutting edges (this is not a radius cutter!) facilitate a smooth operation, a much better service life and time savings of up to 50 % during the roughing procedure. Metal restorations are manufactured within ca. 10-15 min. in extraordinary quality. Please note that the special cutter geometry requires a new strategy and new tool data in the CAM software. This tool does not replace the reliable T6! Diameter Ø 3.0 mm Cutting edges quadruple edge Shaft Ø 6 mm Cutting length: l = 15 mm Total length: 45 mm Max. blank height: 15 mm Blank material: CoCr, titanium Coating type: coated For milling machines: Tizian Cut 5.2 Series, Tizian Cut 5, CORiTEC 550i, CORiTEC 750i
Tizian Blank PMMA Splint, 98 mm x 16 mm in bulk pack, 10 pc.
Tizian Blank PMMA Splint is made of a highly pure themoplastic PMMA which is produced following the highest quality standards. The crystal clear, color-stable material stands out with its homogeneity, low plaque adhesion and low water absorption. Tizian Blank PMMA Splint is an economic alternative for the splint technology. It can be be repaired and extended with PMMA acrylics. Indications: Occlusion splints Drilling templates for navigated implantation Lost wax technique in casting technology Processing: Due to the chemical and physical properties of thermoplastic PMMA, there is a risk of melting the material during dry machining and thus smearing the mills. Therefore, it is important to use only single-edged mills. If necessary, the milling strategy must be adjusted with a slower cutting speed and a lower feed rate. The material can be processed by wet machining with PMMA mills in a standard strategy without restrictions.
T11 Tizian Cut 5/3.5 PMMA finemilling single point mill, 2,5 mm, 6 mm shaft
Radius cutter single-edged, edge Ø 2.5 mm, shaft Ø 6 mm, total length 53 mm, max. blank height = 25 mm. Processing type: pilot milling Blank material: PMMA, PEEK Coating type: uncoated Ring color: gold For milling machines: Tizian Cut 5.2, Tizian Cut 5.2 plus, Tizian Cut 5 option metal milling (6 mm shaft), CORiTEC 550i, CORiTEC 750i