Tizian Blank Wax grey 98 x 20 mm, Wax, Color: grey

Radius cutter short, double-edged, edge Ø 1 mm, shaft Ø 6 mm, total length 45 mm. Max. blank height = short up to 15 mm, long up to 20 mm. Processing type: fine finishing Blank material: CoCr, titanium Type: coated Coding color: gold For the milling machines: Tizian Cut 5.2, Tizian Cut 5.2 plus, Tizian Cut 5 option metal milling (6 mm shaft), CORiTEC 550i, CORiTEC 650i

T61 - metal roughing tool The complex geometry of the four high-capacity cutting edges (this is not a radius cutter!) facilitate a smooth operation, a much better service life and time savings of up to 50 % during the roughing procedure. Metal restorations are manufactured within ca. 10-15 min. in extraordinary quality. Please note that the special cutter geometry  requires a new strategy and new tool data in the CAM software. This tool does not replace the reliable T6! Diameter Ø 3.0 mm Cutting edges quadruple edge Shaft Ø 6 mm Cutting length: l = 15 mm Total length: 45 mm Max. blank height: 15 mm  Blank material: CoCr, titanium Coating type: coated For milling machines: Tizian Cut 5.2 Series, Tizian Cut 5, CORiTEC 550i, CORiTEC 650i

Tizian Blanks NEM (non-precious metal) are made of beryllium-free and cadmium-free CoCr ceramic alloy according to DIN EN OSP 22674 and EN ISO 9693 for applications with thin cross-sections which are exposed to extreme forces. Examples are removable partial dentures, clasps, thin veneered individual crowns, fixed full arch dentures or bridges with small cross-sections, bars, fixations, implant-supported supraconstructions. Properties: Alloy type: 4Density: 8.8 g/cm³Vickers hardness: 285 HV 10/30CTE- value (25-500 °C): 14,4*10-6 K-1Oxidation without vacuum (Point 4c): 1000 °CMass content of the components (in weight-%)*: Co 63, Cr 29, Mo 6 / Mn x, Nb x, Si x, Fe xTensile strength: 680 MPa0.2 % yield point: 400 MPaElongation at break: 9 %E-module: 250 GPa *X= <, 1%

Tizian Blanks NEM (non-precious metal) are made of beryllium-free and cadmium-free CoCr ceramic alloy according to DIN EN OSP 22674 and EN ISO 9693 for applications with thin cross-sections which are exposed to extreme forces. Examples are removable partial dentures, clasps, thin veneered individual crowns, fixed full arch dentures or bridges with small cross-sections, bars, fixations, implant-supported supraconstructions. Properties: Alloy type: 4Density: 8.8 g/cm³Vickers hardness: 285 HV 10/30CTE- value (25-500 °C): 14,4*10-6 K-1Oxidation without vacuum (Point 4c): 1000 °CMass content of the components (in weight-%)*: Co 63, Cr 29, Mo 6 / Mn x, Nb x, Si x, Fe xTensile strength: 680 MPa0.2 % yield point: 400 MPaElongation at break: 9 %E-module: 250 GPa *X= <, 1%

With a translucency of 35 %.Indications:   Very aesthetic monolithic, fully anatomical crowns, partial crowns and bridges with up to 16-units, frameworks     Recommended for covering discolored tooth stumps or metal structures Advantages of monochromatic precolored blanks Why use precolored material? Applying a penetrating, homogeneous stain to the material does away with the need for processes such as dipping, painting and drying. This does not only save time and effort, but it also helps to avoid potential manual errors during the staining process. This reduces production costs and your customers will appreciate the consistent and reproducible color quality. Since the material comes fully precolored, even finishing or adjustment grinding do not leave light spots, which would have a negative effect on the appearance of the finished product. Industrially precolored zirconium blanks are reproducible. Precolored material is gentle on your sintering furnace and protects its components from damage. Acid-based liquid stains can emit fumes during the sintering process which leave deposits on the the heating elements of the furnace and contaminate them. This can cause undesirable discoloration and/or loss of translucency. Using industrially precolored zirconium ensures consistent color results. Suitable for: open milling system with a blank holder for round blanks with a diameter of 98.5 mm Material:   Zirconium type II, class 5 according to DIN EN ISO 6872   Good flexural strength of >, 1,150 MPa   Very high translucency of 35 % Good aging resistance Thin wall thicknesses for single crowns in the anterior tooth area 0.4 mm and in the posterior tooth area 0.6 mm   Biocompatible    

"For top-class temporaries! PMMA material for highly aesthetic temporaries. 10-fold layer, virtually invisible transitions. Indications: Anterior and posterior temporary crowns Anterior and posterior temporary bridges with up to two consecutive bridge pontics Implantat-supported temporary restorations, maximum recommended wear time: 12 months Therapeutic splints (occlusal splints)  Composition: Copolymer based on PMMA >