No results were found for the filter!
Special tool contra angle for IMPLA 3D Special tool contra angle for IMPLA 3D
Implant tightening aid for contra angle.
pilot drill 1.8 mm pilot drill 1.8 mm
For initiating a pilot hole and marking the bone when determining the implant entry position.
Insertion key, mechanical incl. WS Insertion key, mechanical incl. WS
For direct implant insertions using the contra angle.
Insertion Key for Miniballtop Insertion Key for Miniballtop
Tightening aid for manual insertion of Impla Mini Balltop implants.
Guide key Guide key
Helps safe release of the retention screw on the insertion post on existing implants with reduced primary stability.
torque ratchet torque ratchet
Used for manual insertion of implants, or for torque controlled fixing of abutments.
open-end wrench for IMPLA 3D open-end wrench for IMPLA 3D
For the transfer of the implant.
Locator core tool, threepart Locator core tool, threepart
Wrench for locator abutments and insertion matrices - can be sterilized.
Tissue cutter 5.3 mm Tissue cutter 5.3 mm
Used for flapless opening of the soft tissue.
contra-angle adapter, 1.2 mm, short contra-angle adapter, 1.2 mm, short
Used for tightening all retaining screws and components with a 1.2 mm inner hex connector.
hexagon screwdriver, 1.2 mm, long hexagon screwdriver, 1.2 mm, long
This hexagon screwdriver with ratchet connection has a 1.2 mm hexagon at the tip.
Depth gauge 3,3mm, brown Depth gauge 3,3mm, brown
Depth gauge to check the planned implant insertion depth.
hexagon screwdriver, 2.3 mm, long hexagon screwdriver, 2.3 mm, long
The screwdriver with ratchet connection has a 2.3 mm hex connection.
hexagon screwdriver, 2.3 mm, mechanical hexagon screwdriver, 2.3 mm, mechanical
Screwdriver for automatic and direct insertion of two-piece implants with internal hex connection
Thread former 5.3 mm Thread former 5.3 mm
For precutting screw threads.
Pilot drill 2,0 mm Pilot drill 2,0 mm
Pilot drill without internal cooling for the preparation of implant sites with the IMPLA implant system
Enlargement drill 2,5 mm Enlargement drill 2,5 mm
IMPLA surgical drill, diameter: 2.5 mm
Cortical drill 2,0 / 3,15 mm Cortical drill 2,0 / 3,15 mm
Use on D1 and D2 bones ideally.
Countersink 3,3 mm Countersink 3,3 mm
Specific implant drill for final preparation in accordance with the drill protocol
Countersink cutter 3,4 mm for Cylindrical Countersink cutter 3,4 mm for Cylindrical
Specific implant drill for the final site preparation in accordance with the drill protocol.
Insertion key long, mechanical, 2,0 mm Insertion key long, mechanical, 2,0 mm
Screwdriver to make fine adjustments to the implant in the bone.
Insertion key long Insertion key long
Insertion key (3 mm), mechanical (hex connection) for the insertion posts of the implants.
Enlargement drill short 2.5 mm Enlargement drill short 2.5 mm
Extension drill without internal cooling, diameters 2.5 mm, 3.15 mm, and 4.25 mm for all IMPLA Micro Retention implant lines.
Enlargement drill short 2.75 mm for Cylindrical Enlargement drill short 2.75 mm for Cylindrical
Extension drill short, without internal cooling, diameters 2.75 mm, 3.0 mm, 3.7 mm, 3.9 mm, 4.6 mm and 4.9 mm for all IMPLA Cylindrical implant lines.
Insertion key 2.5 mm short Insertion key 2.5 mm short
Ratchet tool to change the insertion depth or the hex position of IMPLA Cone Connection implants after removal of the insertion post (part of the packaging). The tip of this tool fits precisely into the implant geometry. It can be used...
Insertion key 2.0 mm long Insertion key 2.0 mm long
Ratchet tool to change the insertion depth or the hex position of IMPLA Cone Connection implants.
Viewed