Denture Acrylics

The MicroClean cleaning system cleans dentures automatically, gently, and in a way that is appropriate for the material involved. Even the strongest contaminants such as plaque and tartar can be automatically removed by MicroClean without any difficulty. Even in difficult to reach areas. No matter whether it is a denture that the patient has already worn or a newly made one - MicroClean cleans, polishes and pre-polishes e.g. crowns or bridges quickly and without material abrasion right into the finest inter-dental areas, fissures and telescopic tips. Benefits: Perfect automatic cleaning Especially for difficult, difficult to access areas (e.g. load distribution clasp) Top quality surface conditioning without any frictional loss! (telescopic restorations) Easy removal of fixing cement Makes ultrasonic cleaning unnecessary Significantly more efficient work, free from interruptions Basic equipment: Needles long, 150 g Plastic container Tweezers, 18 cm Holding magnet, complete Stand-up display Measuring cylinder, 50 ml 2 x 500 ml cleaning fluid (green and orange) Technical Data: Voltage: 230 V~ Power output: 200 VA Speed: 1450 rpm Number of phases: 1 phase-N+PE Neutral conductor: loadable N~  Protective conductor: separate protective conductor (PE green/yellow) Protection class: I Protection type: covered Frequency: 50/60 Hz Noise level: < 65 dB (A) Dimensions (w x d x h): 185 x 175 x 195 mm Weight: 7 kg

Reduction of residual monomer - by means of secondary treatment of cold curing prostheses. Allergic reactions and sensitivities because of newly produced dental prosthesis with acrylic parts become more and more common. They pose a real problem for the wearer. Within 16 hours, Schütz Dental's Monomer Extractor can reduce the residual monomer in denture acrylics from more than 4.5 % to less than 0.4 %* in many cases. Your benefits: Irritations of the palate and a burning sensation in the mouth are avoided almost completely. Increased wearing comfort of the prosthesis. Allergic reactions are reduced significantly. No additional workload. The procedure runs automatically over night. This secondary treatment can be billed to the patient in some cases. Decreases the residual monomer content  from more than 4.5 % to less than 0.4 %* duing a 16 hour temperature-controlled immersion in water and with an optional addition of active oxygen. *Depends on the acrylic material used. Tested by „GDF Gesellschaft für dentale Forschung und Innovationen GmbH“, Rosbach/Germany.

Aesthetic System for Acrylic TemporariesBiocompatible** – Non-toxic** – Reduced Plaque Accumulation** – Fluorescent Aesthetic Temporary Restorations""Enamel plus Temp"" helps you to imitate the tooth function as well as its aesthetic appearance. Temporary restorations made of ""Enamel plus Temp"" are an excellent basis for a holistic, diagnostic treatment. This offers the opportunity to dentist and patient to make adjustments in the temporary restoration which can be transferred to the permanent restoration later.Your benefits: Only a few steps to obtain an outstanding color match Special incisal shades Natural shades, close to natural tooth shades Exceptionally high surface hardness for durable restorations Polishes quickly and easily Extraordinary physical properties Content: 4 x Dentin, 50 g: UD2 (A2), UD3 (A3), UD3.5 (A3.5), UD4 (A4) 1 x Universal Enamel UE2, 50 g 1 x Opalescent Blue Enamel, 50 g 1 x Self-curing monomer liquid, 100 ml ** Cytotoxicity test with direct cell contact ASTM F 813-83 and with Agar diffusion according to ASTM F895-84 with test extraction irritation and allergy sensititzation test according to Buehler, OECD 406-92 and DIR CEE 93/21.

Made from stainless steel. Only for cold polymerization at a pressure up to 2 kg/cm². Dimensions: Height: 235 mmWidth: 245 mmLength: 420 mmDiameter: 245 mmVolume: 6 lMaterial: stainless steelGewicht: 2406 g

You can make partial and full prostheses with this flow technique flask. Clarity for better control of your technical dental work.

A robust relining system which allows you to do your regular and permanently soft relining work, quickly and accurately.

For bonding titanium abutments to individualized zirconium dioxide abutments and supra-constructions. The full system consists of: Sebond Implant: The bonding agent prepares the zirconium dioxide surface for secure bonding. Alphalink Implant: The fixing composite bonds your framework to the abutment. Indications: Glue individual abutments to the corresponding adhesive base. Use this system for secure adhesion of supra constructions to abutments. Bond the following materials: Zirconium dioxide Precious metal Non-precious alloys Titanium Ceramics Unequaled bond strength values: Zirconium dioxide: >, 20 MPa Titanium: >, 30 MPa Benefits at a glance: The material offers the highest level of safety, as it was especially developed for bonding The system adapts to the user: Intraoral use = quick curing Use on models = longer working range High bond strength Long term stability due to the specially adapated formula Saves time Facilitates accurate work:The pasty consistency lets you remove excess material very easily Content: 2 x 4 g syringe Alphalink Implant, 10 mixing tips

For placing in elastic rubber impression materials. The connector socket is milled in one piece with dowel pins. For use as part of the Pin Set process.  , Contents: 1000x Dowel Pins

Aesthetic system for acrylic temporaries Produce long-term temporary crowns and bridges with the fluorescent Tizian Blanks PMMA in 5 special shades. They stand out with their extraordinary physical properties. Indications: long-term temporary restorations (up to six months), suitable for veneering with composite. Your benefits: Ready to be used in milling unit without curing Fast working time and low cost Excellent mechanical properties for long terms temporary Antagonist friendly Low monomer residual Physical data: Hardness Vickers: 140 MPaFlexural strength: Min. 125 MPaE-module: 2500 MPaWater solubility: 1,1 ?g/mm3Water absorption: 21.2 ?g/mm3Residual monomer: 0,6%  

Brass guide pins for saw cut models for use as part of the pin drill process

Basket insert for Monomer Extractor for the reduction of residual monomer by secondary treatment of cold curing prostheses.

All-in-one. All-rounder. New improved formula. Universally applicable.     Your advantages: Now even faster finishing and polishing for top results Wide range of indications Even more universal application Even easier to use Even better fit Safer processing: high error tolerance   Indications: All-in-one: Excellent for all conventional acrylic techniques.   Injection procedures Repairs Completing frameworks Full dentures Relinings Splints

Cold curing modelling acrylic. for modelling telescopic crowns. The acrylic can be fully burned out and is easy to model. Benefits: PaintAcyrl is easy to work with and saves you time. It can be applied in coats and re-worked. It has outstanding swelling property. The polymer is extremely fine-grained The brush tip, moistened with monomer, is saturated with the polymer in a flash. PaintAcryl does not run or disperse It burns off without leaving any trace, giving a smooth cast surface. No noticeable shrinkage during polymerisation. Rapid hardening in max. 4 minutes, completely non porous. Models are highly stable and extremely accurate. Even the thinnest models can be taken out without any warping. Due to the high degree of transparency of the material, a very high level of wall thickness control can be achieved when modelling and preparing.

Alphalink bonding adhesive is a two-part composite. For gap-free joints, for example between secondary crowns and tertiary frameworks directly in the mouth or on a technical dental model. ,The two components are filled into one double chamber syringe each. When extruded, they mix homogeneously in the ideal consistency in the mixing tube.

Two part composite for fixing prosthetic holding elements.

This acrylic fluid extends the working time of your Futura Basic acrylic. Particularly suitable for characterization with FuturaIntensiv powder.

Hardener for your Profit Set. Liquid modelling acrylic with a cyanoacrylate base with spray activator. For fixing attachments, bonding crowns and making solder bases. Set contains: 50ml rapid hardener

Hardenerrefill pack for your AlphaDie Set Polyurethane based model stump material with filler. Sharp imaging, strong edges, extremely hard with high break and elongation stability. Contents: 100 ml hardener

For the production of permanently soft reliners.